Configure the Mesh Node

The GM03 Mesh Node’s user interface allows you to update the GM03 firmware, view SIM Card information, view and download logs, check unit status, and point the backhaul antenna. To work with the GM03 Mesh Node, we recommend using any of the following web browsers:

• Google Chrome (latest version)
• Mozilla Firefox (latest version)

Log On to the GM03 Mesh Node

To log on to the Mesh Node:

1

Apply power to the Mesh Node. Once the Mesh Node’s 2.4 GHz Wi-Fi interface is operational, the Power and Wi-Fi LEDs will be on.

2

Open the Network and Internet settings on the laptop and click the GM03’s SSID. The SSID of the Mesh Node’s Wi-Fi interface will be “GXCTR0-xxxxxx”, where xxxxxx is the MAC address of one of the Mesh Node’s Ethernet ports. This MAC address is printed on the GM03’s label.

3

Click the SSID to connect to the Mesh Nodes Wi-Fi network and it will prompt you for a password. The default Wi-Fi password at the time this guide was published is “fishAnchorDish17”.

4

Once you are connected, you can access the Mesh Node’s Local Control Interface (LCI). In the browser’s address bar, type “192.168.1.1” and press Enter to open the LCI Login webpage.

NOTE: Because the GM03 LCI uses a self-signed security certificate, a Chrome browser will display a “Your connection is not private” warning message and a Firefox browser will display a “Warning: Potential Security Risk Ahead” message. The GM03 LCI is not an actual security risk. In Chrome, click the Advanced button, and then click the Proceed to 192.168.1.1 (unsafe) link. In Firefox, click the Advanced button, and then click the Accept the Risk and Continue button.

5

When prompted, enter the Username “onyx” and the Password “shinyStoneBox22” and click Login.

NOTE: Your session will expire, and you will be automatically logged out of the system after 30 minutes. There is currently no logout option.

Connect using Wired Ethernet

Logging on via Ethernet can be used for debugging the system if access over Wi-Fi is not working or is not desired. In normal operation, the Ethernet port is reserved for connecting the Mesh Node to the Mesh AP.

To access the Mesh Node using the wired Ethernet port do the following:

1

Connect the laptop to the Mesh Node’s Ethernet 1 port using an Ethernet cable.

2

Enter the Mesh Node’s Ethernet port address “10.0.5.1”. The laptop needs to be on the same “10.0.5” Subnet to communicate with the Mesh Node.

Navigate the User Interface

Once you’ve successfully logged in, links at the top right side of any of the Mesh Node’s webpages are used to open the Status, FW Update, Settings, CBRS AP, System, Antenna, and About pages.

Change the Password

The GM03 has a Wi-Fi network password and a Local Control Interface password that can be changed in the Privacy section of the Settings page.

Change the Wi-Fi Password

To change the Wi-Fi password:

1

Click the Settings link at the top right side of any of the Mesh Node’s webpages to open the Settings page.

2

In the Privacy section, click the Change Wi-Fi password link.

3

Enter the current Wi-Fi password and then click next.

4

Enter the new password and then re-enter the password.

5

Click Confirm to change the password.

Change the Local Control Interface Password

To change the LCI Password:

1

Click the Settings link at the top right side of any of the Mesh Node’s webpages to open the Settings page.

2

In the Privacy section, click the Change LCI password link.

3

Enter the current LCI password and then click next.

4

Enter the new password and then re-enter the password.

5

Click Confirm to change the password.

Reboot the Mesh Node

To reboot the Mesh Node:

1

Click the FW Update link at the top right side of any of the Mesh Node’s webpages to open the Settings page.

2

Click the Reboot button located on the lower left side of the page.